Automatic Sliding Door Mechanism D5 is a European Style mechanism.
Features
Components Position in the Guide Rail
Components of Automatic Sliding Door Mechanism D5
Components' Details of Sliding Door Mechanism D5
![]() | Microcomputer Controller The microcomputer controller of the automatic door is used to receive the detection signal of a sensor or other The controller itself comes with 12V, 24V Newly added ports for security protection |
Brushless DC motor Small size and high power DC brushless The internal fully sealed structure is durable With safety protection circuit device, long-term trouble-free operation can be achieved even | ![]() |
![]() | Microwave Sensor 24.125GHz microwave sensor module imported from Germany, not affected by temperature and humidity influences. The highest installation height is 4 meters, which is easy to install, stylish and beautiful, and resistant to microwave emission. |
Track It is made of 6063 -T5 high-purity aluminum alloy. The size of track 82 * 88MM, unlimited use of installation space. Split track type design, add rubber silent damping bar, make the operation more stable, more convenient. | ![]() |
Automatic Sliding Door Mechanism D5 is suitable for a single door with a weight of up to 120kg.
D5 | Single | Double |
Max.Weight of Body | 120kg | 2*100kg |
600-1800mm | 600-1800mm | 1000-3000mm |
Opening Speed | 175-440mm/s (adjustable) | |
Clothing Speed | 175-440mm/s (adjustable) | |
Holding Time | 0~8s (Adjustable) | |
Motor Power | 65W | |
Power supply | AC90V~240V 50~60HZ | |
Operating Temperature | -20℃+50℃ |
Sectional view of Automatic Sliding Door Mechanism D5
1. Installation of guide rail and stoppers
• Infrastructure requirements: the installation surface must be smooth and firm,concrete walls must be able to be connected with M8 expansion pipes,structural steel beam must be able to be fixed with M8 screwes.
• Cut the guide rail according to the door design requirements, and fix the guide rail onto the wall or steel structure with M8 screws flatly and firmly.
Install the guide rail at a height of DH+16mm from the ground 1. Drill holes on the guide rail and steel structure ( or wall | ![]() |
2. Installation of hangers
1 Insert the bolts (M8X20) for hanger into the sliding door panel top and reserve gap at least 6mm;
2 Insert these bolts into the square holes at hangers' bottom too, note the door levelness and position
3 Tighten above bolts according to below hanger position figure:
3. Installation of stopper
Fix two stoppers at the door full open position and full close position, tighten the bottom bolt M8X10 of the stopper, ensure the sliding door panel will not slide off from the guide rail
4. Installation of motor and controller
Insert four M6X12 bolt sets ( see below figure ) at the left of the guide rail and the controller on the bolt sets then tighten the bolts.
5. Installation of idle pulley
Insert two M6X12 bolt sets ( see below figure ) at the right of the guide rail, hang the idle pulley on the bolt sets.
6. Installation of belt
6.1 Belt connector fixation
Cut the belt according to your need, insert the belt into the belt connector(s), hang the belt ring onto
the motor wheel and idle pulley wheel.
6.2 Belt tension adjustment
1 . Pull the ilde pulley to the right end of the guid rail to make belt tight, then tighten the bolt set M6X12
2. Loosen the four bolt C
3. Rotate the bolt D clockwise to move the adjustment plate to the right, the tension is increasing until
the tension is suitable;
4. Tighten the bolt C.
Features of Automatic Sliding Door System DSL-200L
Components of Automatic Sliding Door System DSL-200L
Automatic Sliding Door System DSL-200L is suitable for a single door with a weight of up to 150kg.
DSL-200L | Single | Double |
Max.Weight of Body | 150kg | 2*120kg |
Opening Width | 600-1800mm | 1000-3000mm |
Opening Speed | 200-500mm/s (adjustable) | |
Clothing Speed | 200-500mm/s (adjustable) | |
Holding Time | 0-9S (adjustable) | |
Motor Power | 65W | |
Manual Opening and Closing Force | <40N | |
Power supply | AC90V~240V 50~60HZ | |
Operating Temperature | -20℃+50℃ |
Secional view of Automatic Sliding Door System DSL-200L
1.Type of door: frameless door or framed door
2.Size of doors
Reason | Inspection | |
Door body don't move | Power is not on | Check the power cable, check the power switch |
Foreign matters on the rail | Turn off the power, push the door by hand to see if the door moves smoothly | |
Automatic protection | Check if there is any obstacle on the way | |
Door is locked | Check if there is an external lock | |
Door can't be fully opened | Half-open mode | Check if it's set to half-open modeDoor can't be closed./ Door operates abnormally |
Door can't be closed./ Door operates abnormally | Sensor misoperation | Check for continuous moving items within the sensing range |
Short-circuit of control signal line | Disconnect the signal line and see if it worked | |
Microwave interference source around the door | Check the microwave interference source | |
Continuous operation of the safe beam | Confirm whether the safe beams are covered by dirt | |
Confirm whether the safe beams deviate from the right angle | ||
Door runs not smoothly | High running resistance | Check if there are foreign matters on the rail |
Check if there is an obstacle on the door body | ||
Inappropriate speed for opening and closing | Check the speed adjustment |